The FPS rate of the Nikon D90 Digital Single Lens Reflex (DSLR). To get the full 4.5 FPS on the D90, switch your cameras mode dial to either S, A, or M. Lets say you have it in A (Aperture Priority). Dial down your aperture to the lowest your lens F stop is, like F2.8. Once you have done that, adjust your ISO according to your lighting to get a proper exposure without a lot of noise. Secondly, make sure that your shutter speed is 1/250th of a second or faster. Then, hold down the release mode button (Top Right on body with 3 frames) and move the main command dial, on back, to the multiple frames with an “H” image on the LCD screen on top. You will now be able to shoot at 4.5 frames per second!
Daleon1
December 18, 2012 at 9:51 pm
Hold down the AE-L/ AF-L then try it or aim to a light source It will go faster….
DjDime92
December 18, 2012 at 10:33 pm
more grain i meant more noise, haha.. oke, i tested high and low iso.. and i think it’s best to be left on auto.. cause then shutter speed depends on light only.. thanks again. D90’s quite a good camera tho
Nick Wagner
December 18, 2012 at 10:42 pm
ok.. Set your ISO by holding down the zoom out button – you can see ‘ISO’ above the button which is on the back to the left of the lcd. second from the bottom. As you hold it down, use the main command dial (top right dial on the back of the camera) to change it. ISO isn’t shutter speed – it is the camera’s sensor’s sensitivity to light. So the higher speed does mean faster shooting but not more grain. There’ll be more noise (grainy look) with higher ISOs.
DjDime92
December 18, 2012 at 11:35 pm
getting to know this baby, step by step.. thanks!
Nick Wagner
December 18, 2012 at 11:48 pm
Well it depends on your situation. Do you understand how the three – shutter speed, aperture and ISO correlate? If your shutter speed is to slow (blurry images), you can increase the ISO to make your camera more sensitive to light to allow for a faster shutter speed and thus a sharper image!
DjDime92
December 19, 2012 at 12:07 am
oke, i found it.. so is it better to leave it on auto or..? i mean ISO
DjDime92
December 19, 2012 at 12:40 am
i read it, thanks.. could u tell me how exacly to set my ISo? thats shutter speed, right? higher speed – faster shooting, more grain, right?
Nick Wagner
December 19, 2012 at 1:31 am
Alright.. Check out my directions in the details tab. If that doesn’t work, the only thing I could guess you’re doing wrong is shooting in too dark of a room. Manual mode gives you full control over the camera. So you have to set the shutter speed, ISO, and aperture among other things. I might just post a how-to video with a step by step format to be able to shoot 4.5 FPS.
DjDime92
December 19, 2012 at 1:57 am
uhm, well, i played with it last night, think i got it to work.. but only in S or M mode, wich are i dont know for what, but very low amount of light is registred on photos.. and no-flash mode does something like 3.5-4 fps (highspeed)
Nick Wagner
December 19, 2012 at 2:20 am
What is your shutter speed?
DjDime92
December 19, 2012 at 3:11 am
how did this work for fucking sake!?? my d90 has delay of like half a second between shots in highspeed continuous.. -_-.. WHY!?
takjub
December 19, 2012 at 4:04 am
“adjust your ISO according to your lighting to get a proper exposure without a lot of noise.”
how to do that?
takjub
December 19, 2012 at 5:03 am
“adjust your ISO according to your lighting to get a proper exposure without a lot of noise.”
how to do that?
lazymuthaz
December 19, 2012 at 5:11 am
I’m actually new with DSLR cameras! I just got my D90 and can you teach me how to set my D90 in order to do the same thing in your video? Thanks!!
lazymuthaz
December 19, 2012 at 5:30 am
I’m actually new with DSLR cameras! I just got my D90 and can you teach me how to set my D90 in order to do the same thing in your video? Thanks!!
lazymuthaz
December 19, 2012 at 6:21 am
I’m actually new with DSLR cameras! I just got my D90 and can you teach me how to set my D90 in order to do the same thing in your video? Thanks!!
thesmartkiller
December 19, 2012 at 6:56 am
thaaaanks aloot my friend
Nick Wagner
December 19, 2012 at 7:07 am
Step By Step #1 Press the “Menu” button on the left of the LCD. #2 Highlight the pencil/Custom settings menu (third one down from top) press to the right on D Pad. #3 Highlight the last sub menu (F) its purple, Press OK. #4 Highlight (F6) “No Memory Card?” and press OK. #5 Highlight Enable relase, and press OK. You are now free to shoot without a memory card inserted into the camera. If you have anymore questions, dont be afraid to ask!
Nick Wagner
December 19, 2012 at 7:22 am
Step by step. #1 Press the menu button on left hand side of LCD. #2 Go to custom setting menu (The Red menu, with a pencil as logo) #3 Go down to sub section (f) – its purple. press ok. #4 Go down to (F6) – to the right it will say “No Memory Card”? – Press OK. #5 Highlight Enable Relase and press OK. You are free to shoot without your memory card inserted into the camera
thesmartkiller
December 19, 2012 at 7:51 am
how you did it with out the card ??
I tried it on mine but it didn’t work ,,,
llamasrage
December 19, 2012 at 8:15 am
I actually just bought an extreme 3 because it was on sale, and if I get any extra frames out of it then it’s only 1 or 2 at the most. It seems like the camera’s internal buffer limits it more than the speed of the card.
Nick Wagner
December 19, 2012 at 8:59 am
Yes it is, even while shooting in RAW. Except you’ll be more limited to the total amount of pictures you can take without the Buffer filling up, so if you’re shooting at Max Resolution, get a fast card, like a Sandisk Extreme 3
sseeww5400
December 19, 2012 at 9:13 am
is it so fast on max. resolution?
AZNFlipy12
December 19, 2012 at 10:07 am
horray for fractions cause .250 x 4=1 so 4 frames in one second